Star Micronics TSP200-24 Uživatelský manuál stáhnout pdf (Strana 11)

– 7 –

ENGLISH

3-3. Optional AC Adapter

NOTE:Before connecting/disconnecting the AC adapter, make sure that power

to the printer and all the devices connected to the printer is turned off.

Also make sure the power cable plug is disconnected from the AC outlet.

1 Connect the AC adapter to the power cable.

Note: Use only the standard AC adapter and power cable.

2 Connect the AC adapter to the connector on the printer.

3 Insert the power cable plug into an AC outlet.

Fig. 3-6

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 137 138

TSP200-24 1
Trademark acknowledgments 2
Table of Contents 3
1. Unpacking and Inspection 5
3. Printer Connection 7
Fastener 9
Pull and cut 9
Fig. 3-5 10
3-3. Optional AC Adapter 11
4. Near-End Sensor 12
5. Loading Paper 13
Paper exit 15
Paper feeder 15
Printer mechanism 15
Auto cutter unit 15
5-3. 76mm Width Support 18
Support spacer 19
Where the catch locks 19
5-4. Clearing Paper Jams 20
6. Control Panel 21
1 Test print 22
2 HEX dump 23
6-3. Errors 24
7. Cautions 26
8. Command summary 27
Other Commands 30
8-2. ESC/POS Mode 31
Table des matières 33
1. Déballage et inspection 35
FRANÇAIS 36
3. Connexion de l’imprimante 37
Figure 3-5 40
Figure 3-6 41
4. Capteur de fin de rouleau 42
5. Mise en place du papier 43
6. Tableau de commande 51
1 Essai d’impression 52
2 Vidage hexadécimal 53
Approx. 1 Sec Approx. 1 Sec 54
Approx. 250 msApprox. 250 ms 54
Approx. 2 Sec Approx. 2 Sec 54
Approx. 125 msApprox. 125 ms 54
7. Precautions 56
8. Resume des commandes 57
Autres commandes 60
8-2. Mode ESC/POS 61
Inhaltsverzeichnis 63
1. Auspacken und Prüfung 65
3. Druckerverbindung 67
Screws 68
Screwdriver 68
Schrauben 68
Schraubenzieher 68
One loop 69
Ferrite core (28mm diameter) 69
Abb. 3-5 70
3-3. Optionales Netzteil 71
4. Papiervorrat-Sensor 72
5. Papier einlegen 73
5-3. 76 mm Breit-Stütze 78
Wo die Sperre einrastet 79
Automatische 79
Abschneideinheit 79
Stütz-Distanzstücke 79
5-4. Papierstau beheben 80
6. Bedienfeld 81
1 Testdruck 82
2 HEX-Datendump 83
6-3. Fehlermeldungen 84
7. Behandlung des Druckers 86
8-1. Star-Betriebsart 87
Weitere Befehle 90
8-2. ESC/POS Betrieb 91
Fig. 1-1 95
3-1. Cavo di interfaccia 97
ITALIANO 100
Fig. 3-6 101
5. Caricamento della carta 103
5-2. Rifornimento della carta 107
6. Pannello di controllo 111
1 Stampa di prova 112
2 Scaricamento esadecimale 113
6-3. Errori 114
7. Precauzioni 116
8. Elenco dei comandi 117
Altri comandi 120
8-2. Modo ESC/POS 121
APPENDIX 123
Paper Specifications 125
Power Supply Specifications 126
DIP switch array 127
DIP switch #1 127
DIP Switch #2 128
Appendix C: Interface 129
Interface Connections 131
74LS-equivalent 132
Ferrite core 134
Ground wire 134
Appendix E: Cleaning 136
1999.07.30 138
Printed in China, 80870155 138

Komentáře k této Příručce

Žádné komentáře

Star Micronics TSP200-24 Uživatelský manuál Strana 11

Komentáře k této Příručce

Související produkty a manuály pro Tisk a skenování Star Micronics TSP200-24