Star Micronics TSP200-24 Uživatelský manuál stáhnout pdf (Strana 10)

– 6 –

ENGLISH

■ Clamp the ferrite core onto the peripheral unit cable, looping the cable as

shown in Fig. 3-1.

• When installing the ferrite core be careful not to damage the cable.

• The ferrite core should be anchored firmly in place with the fastener that

comes with it, as shown in Fig. 3-3 and Fig. 3-4.

• Do not forget to loop the cable.

Fig. 3-5

Fastener

One loop

Ferrite core

Separate ground wire

Peripheral unit drive

circuit connector

Screw M3×4

Connector

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 137 138

TSP200-24 1
Trademark acknowledgments 2
Table of Contents 3
1. Unpacking and Inspection 5
3. Printer Connection 7
Fastener 9
Pull and cut 9
Fig. 3-5 10
3-3. Optional AC Adapter 11
4. Near-End Sensor 12
5. Loading Paper 13
Paper exit 15
Paper feeder 15
Printer mechanism 15
Auto cutter unit 15
5-3. 76mm Width Support 18
Support spacer 19
Where the catch locks 19
5-4. Clearing Paper Jams 20
6. Control Panel 21
1 Test print 22
2 HEX dump 23
6-3. Errors 24
7. Cautions 26
8. Command summary 27
Other Commands 30
8-2. ESC/POS Mode 31
Table des matières 33
1. Déballage et inspection 35
FRANÇAIS 36
3. Connexion de l’imprimante 37
Figure 3-5 40
Figure 3-6 41
4. Capteur de fin de rouleau 42
5. Mise en place du papier 43
6. Tableau de commande 51
1 Essai d’impression 52
2 Vidage hexadécimal 53
Approx. 1 Sec Approx. 1 Sec 54
Approx. 250 msApprox. 250 ms 54
Approx. 2 Sec Approx. 2 Sec 54
Approx. 125 msApprox. 125 ms 54
7. Precautions 56
8. Resume des commandes 57
Autres commandes 60
8-2. Mode ESC/POS 61
Inhaltsverzeichnis 63
1. Auspacken und Prüfung 65
3. Druckerverbindung 67
Screws 68
Screwdriver 68
Schrauben 68
Schraubenzieher 68
One loop 69
Ferrite core (28mm diameter) 69
Abb. 3-5 70
3-3. Optionales Netzteil 71
4. Papiervorrat-Sensor 72
5. Papier einlegen 73
5-3. 76 mm Breit-Stütze 78
Wo die Sperre einrastet 79
Automatische 79
Abschneideinheit 79
Stütz-Distanzstücke 79
5-4. Papierstau beheben 80
6. Bedienfeld 81
1 Testdruck 82
2 HEX-Datendump 83
6-3. Fehlermeldungen 84
7. Behandlung des Druckers 86
8-1. Star-Betriebsart 87
Weitere Befehle 90
8-2. ESC/POS Betrieb 91
Fig. 1-1 95
3-1. Cavo di interfaccia 97
ITALIANO 100
Fig. 3-6 101
5. Caricamento della carta 103
5-2. Rifornimento della carta 107
6. Pannello di controllo 111
1 Stampa di prova 112
2 Scaricamento esadecimale 113
6-3. Errori 114
7. Precauzioni 116
8. Elenco dei comandi 117
Altri comandi 120
8-2. Modo ESC/POS 121
APPENDIX 123
Paper Specifications 125
Power Supply Specifications 126
DIP switch array 127
DIP switch #1 127
DIP Switch #2 128
Appendix C: Interface 129
Interface Connections 131
74LS-equivalent 132
Ferrite core 134
Ground wire 134
Appendix E: Cleaning 136
1999.07.30 138
Printed in China, 80870155 138

Komentáře k této Příručce

Žádné komentáře

Star Micronics TSP200-24 Uživatelský manuál Strana 10

Komentáře k této Příručce

Související produkty a manuály pro Tisk a skenování Star Micronics TSP200-24